D-Link DWR-933 User Manual Download

Page: 69 / 71

D-Link DWR-933 User Manual

Appendix A - Technical Specifications

Technical Specifications

Radio Frequency Bands

1,2

LTE Mode:

• Category 6: Band 1/3/7/8/20/28/38

• CA: B1+B8, B1+B20, B3+B8, B3+B20, B3+B7, B7+B20, B38+B38, B3+B3, B7+B7,

B3+B28

WCDMA/HSPA/HSPA+/DC-HSPA Mode:

• Band 1/8

• Downlink: 42 Mbps

• Uplink: 5.76 Mbps

GSM/GPRS/EDGE Mode:

• 900 MHz/1800 MHz

Internal Antenna

• LTE: 1T2R

• Wi-Fi: 2T2R

Wi-Fi Standards

1,2

• 802.11ac/n/g/b

• 2.4 GHz / 5 GHz

• Up to 867 Mbps in 802.11ac (2x2) mode

• Up to 300 Mbps in 802.11n (2x2) mode

• Up to 54 Mbps in 802.11g mode

• Up to 11 Mbps in 802.11b mode

Wireless Security

• WPA & WPA2 (Wi-Fi Protected Access)

• 64/128 bit WEP (Wired Equivalent Privacy)

Firewall

• Port Range Forwarding

• DMZ

• UPnP

External Interface

• Micro-USB port (DC 5 V 1 A external power adapter and USB to Micro USB cable)

• Standard 6 pin micro-SIM/USIM card interface

• microSD Card Slot (Up to 64 GB)

Status Indicators

• 0.96 inch OLED display

• Resolution: 128 x 64 Pixels

Battery

• Capacity: 2800 mAh

Dimensions (L x W x H)

• 105 x 64 x 14 mm (4.13 x 2.52 x .55 in)

Weight

• 140 g (.3 lb)

Operating Conditions

• Operating Temperature: -10 to 45 ˚C (14 to 113 ˚F)

• Operating Humidity: 5 % to 95% (Non-condensing)

Certifications

• NCC

• BSMI

• RoHS

Supported frequency band is dependent upon regional hardware version.

Data rates are theorhetical. Data transfer rate depends on network capacity and signal strength.

• RO

Summary of Contents for DWR-933








































































Search results

Summary of Contents for DWR-933

Reviews:

Related manuals for DWR-933

Brands by name

Popular brands

D-Link DWR-933, User Manual

Search results

Summary of Contents for DWR-933

Reviews:

Related manuals for DWR-933

Brands by name

Popular brands