D-Link DPN-1021G User Manual Download Page 106

Page: 106 / 145

DPN-1021G

GPON ONT VoIP Gateway with 1 GPON

Port, 1 10/100/1000Base-T Port, 1 10/100Base-TX Port,
and 1 FXS Port

User Manual

Configuring via Web-based Interface

Parameter

Description

Volume Settings

Speaker

Specify the earphone volume for the phone connected to the FXS
port of the gateway.

Microphone

Specify the microphone sensitivity for the phone connected to the
FXS port of the gateway.

In the

Codecs Settings

section, you can configure work of voice codecs in use.

Figure 77. The

VoIP / Audio Settings

page. The

Codecs Settings

section

To change parameters of a codec, left-click the relevant line in the table.

Figure 78. The window for changing the codec parameters.

Page

106

of 145

Summary of Contents for DPN-1021G


















































































































































Search results

Summary of Contents for DPN-1021G

Reviews:

Related manuals for DPN-1021G

Brands by name

Popular brands

D-Link DPN-1021G, User Manual

Search results

Summary of Contents for DPN-1021G

Reviews:

Related manuals for DPN-1021G

Brands by name

Popular brands