D-Link DIR-620 User Manual Download Page 27 | Manualshive

Page: 27 / 225

background image

DIR-620

Wireless N300 Router with 3G/CDMA/LTE Support

and USB Port

User Manual

Installation and Connection

PC with Wi-Fi Adapter

1. To connect via an LTE, 3G GSM or CDMA network: connect your USB modem to the USB

port

7

located on the left side panel of the router.

!

If you need to connect or change a USB modem to another one when the router is powered
on, power off the device, connect the modem to the USB port, and power on the router.

2. Connect the power cord to the power connector port on the back panel of the router, then

plug the power adapter into an electrical outlet or power strip.

3. Turn on the router by pressing the

ON/OFF

button on its back panel.

4. Turn on your PC and wait until your operating system is completely loaded.

5. Turn on your Wi-Fi adapter. As a rule, modern notebooks with built-in wireless NICs are

equipped with a button or switch that turns on/off the wireless adapter (refer to your PC
documents). If your PC is equipped with a pluggable wireless NIC, install the software
provided with your Wi-Fi adapter.

7 It is recommended to use a USB extension cable to connect a USB modem to the router.

Page

27

of 225

«
...
25
26
27
28
29
...
»

Summary of Contents for DIR-620


































































































































































































































Reviews:

No comments

Related manuals for DIR-620

Brand: Arris Pages: 2

Brand: Edimax Pages: 49

Brand: Hamlet Pages: 10

UniFi AP FlexHD

Brand: Ubiquiti Pages: 22

Brand: Koma Pages: 2

Brand: Linksys Pages: 544

Brand: Linksys Pages: 112

Brand: PoeWit Pages: 5

Brand: MUNIC Pages: 14

Brand: ActionTec Pages: 2

Brand: Nimbus Water Systems Pages: 10

Brand: Ebyte Pages: 15

Brand: Ebyte Pages: 15

Brand: Ebyte Pages: 9

E104-BT12LSP-TB

Brand: Ebyte Pages: 8

Road Runner Mobile

Brand: Sierra Wireless Pages: 9

Brand: Sierra Wireless Pages: 11

Brand: Telstra Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands