manualshive.com logo in svg

Cypress CapSense Express SmartSense CY3280-MBR2, Manual

Share
Download
Cypress CapSense Express SmartSense CY3280-MBR2 Manual Download Page 19

CY3280-MBR2 CapSense Express with SmartSense Auto-Tuning Kit Guide, Doc. # 001-71857 Rev. *C

19

Kit Operation

Figure 3-5.  Toggle (Touch ON/OFF) Enabled

3.2.3

Flanking Sensor Suppression (FSS)

3.2.3.1

Enable Flanking Sensor Suppression

Go to the 

Device Config

  tab;  select  the 

Flanking Sensor Suppression

 checkbox to enable the

FSS feature for the desired number of buttons.

Figure 3-6.  FSS Enabled

3.2.3.2

Test CapSense Buttons with FSS Enabled

1. Touch a FSS-enabled CapSense button; the respective LED turns on.

2. Without removing the touch, touch another FSS-enabled button; the LED does not glow for the 

second button.

3. Remove the touch from the first button. Now, touch any other FSS-enabled button; the respective 

LED glows.

Button LED glows on touch

Button is “on” even after 

Button goes “off“ on second touch

touch is removed

Summary of Contents for CapSense Express SmartSense CY3280-MBR2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands