manualshive.com logo in svg

Cypress CapSense Express SmartSense CY3280-MBR2, Manual

Share
Download
Cypress CapSense Express SmartSense CY3280-MBR2 Manual Download Page 18

18

CY3280-MBR2 CapSense Express with SmartSense Auto-Tuning Kit Guide, Doc. # 001-71857 Rev. *C

Kit Operation

c. Apply the configuration to the kit by following step 7-9.

d. Verify the feature as explained in the sections 

3.2.2

 to 

3.2.10

.

Ensure that you have a new project every time you verify a different feature. Enabling two or more
features may or may not work at the same time. See the 

CY8CMBR2110 datasheet

 to know about

the features, which will not work together.

3.2.2

Toggle (Touch ON/OFF)

3.2.2.1

Enable Toggle (Touch ON/OFF)

Go to the 

Device Config

 tab; select the 

Toggle (Touch ON/OFF)

 checkbox to enable the toggle fea-

ture for the desired number of buttons. The 

Figure 3-4

 shows toggle feature enabled in four buttons.

Figure 3-4.  Toggle (Touch ON/OFF) Feature GUI

3.2.2.2

Test CapSense Buttons with Toggle (Touch ON/OFF) Enabled

1. Touch a CapSense button for which the Toggle (Touch ON/OFF) feature is enabled; the respec-

tive LED turns on.

2. Touch the same button again; the LED turns off. 

3. On the next touch, the LED goes on again. 

Summary of Contents for CapSense Express SmartSense CY3280-MBR2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands