Cygnus M5-C4P Operating Manual Download Page 92

Page: 92 / 140

Cygnus 4+ Operating Manual

M5-CYG4P-M-01_Iss5.doc

The Gain is set to 42 dB.

The A-Scan shows a back wall

echo signal around 100% height

and there is a thickness value.

This is the optimum setting.

The Gain is set to 55 dB.

The A-Scan shows a back wall

echo signal which goes off the

screen, there are also other

earlier smaller echoes that are

becoming significant. The

thickness measurement is still

ok however.

Ideally you would reduce the

gain down to get a 100% high

signal.

Adjusting the Range

Press the Menu key and check that Range is ticked – select it if it

isn’t. Then in the measurement screen with the A-scan displayed
use the

⇧

⇩

keys to adjust the Range as required.

When Range is selected the

range value is highlighted blue.

Here the range is set to 20mm

[20]

Summary of Contents for M5-C4P













































































































































Search results

Summary of Contents for M5-C4P

Reviews:

Related manuals for M5-C4P

Brands by name

Popular brands

Cygnus M5-C4P, Operating Manual

Search results

Summary of Contents for M5-C4P

Reviews:

Related manuals for M5-C4P

Brands by name

Popular brands