manualshive.com logo in svg

Curve D-DF Series, Instruction, Operation And Maintenance Manual

Share
Download
Curve D-DF Series Instruction, Operation And Maintenance Manual Download Page 8

8 

ref: MA-ED-0008-EN-V16.0-MIÑO DESCALCIFICADOR D-DF-M3 & D-UF-M3.pdf 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. PROGRAMMING.

 

 

 
 

Once the power supply adapter has been connected, the programmer must be programmed.  

 
 
 
 
 
 
 
 
 
 

 

Figure 5.

 

Programmer Front panel. 

 
 
 
 
 

 

KEY

 

DESCRIPTION

 

 

ADVANCE.

 

Moves the pointer to set the parameters.

 

 

TIME & DAY.

 

Access to programme the time and day.

 

 

INCREASE VALUES AND CONFIRMATION. 

Increases the value of the parameters to configure. Confirms the programmed values.

 

 

MODE.

 

Access to configure regeneration mode.

 

 

SET REGEN.

 

Access to configure the parameters of the regeneration mode selected.

 

 

SET CYCLE.

 

Access to the configuration of the regeneration cycle times.

 

 

MANUAL REGEN.

 

Forced manual regeneration.

 

Summary of Contents for D-DF Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands