manualshive.com logo in svg

Curve D-DF Series, Instruction, Operation And Maintenance Manual

Share
Download
Curve D-DF Series Instruction, Operation And Maintenance Manual Download Page 22

22 

ref: MA-ED-0008-EN-V16.0-MIÑO DESCALCIFICADOR D-DF-M3 & D-UF-M3.pdf 

 

 

 

8. - INFORMATION DISPLAYED ON THE SCREEN DURING SERVICE PHASE, DEPENDING ON THE 
CONFIGURATION SELECTED.

 

 

8.1. - CONFIGURATION: TIMED: Delayed clockwork.

 

TIME OF DAY 

DAY OF THE WEEK

 

 

TIME UNTIL THE    

NEXT REGENERATION

 

STATE

 

 

 

8.2. - CONFIGURATION: WEEK: weekly clockwork.

 

TIME OF DAY 

 DAY OF THE WEEK

 

 

TIME & DAY UNTIL     
      THE NEXT 

REGENERATION

 

STATE

 

 

 

8.3. - CONFIGURATION: METER IMM: Immediate Volumetric.

 

TIME 

OF DAY

 

DAY OF            VOLUMETRIC 
THE WEEK 

   CONTOL

 

  AVAILABLE 

  VOLUME 

 

STATE

 

 
 
 

8.4. - CONFIGURATION: METER DELAY: Delayed volumetric. 

 

TIME 

OF DAY

 

DAY OF            VOLUMETRIC 
THE WEEK 

   CONTOL

 

AVAILABLE 

DELAYED

 

   VOLUME 

     REG.

 

STATE

 

 

 

When the meter reaches zero the display will show the following. 

 

TIME OF DAY

 

DAY OF THE

 

VOLUMETRIC

 

 

   WEEK

 

      CONTROL

 

 
 

 

TIME AND DAY  

UNTIL THE NEXT 

REGENERATION

 

STATE

 

Summary of Contents for D-DF Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands