manualshive.com logo in svg

Curve D-DF Series, Instruction, Operation And Maintenance Manual

Share
Download
Curve D-DF Series Instruction, Operation And Maintenance Manual Download Page 12

12

 

ref: MA-ED-0008-EN-V16.0-MIÑO DESCALCIFICADOR D-DF-M3 & D-UF-M3.pdf 

 

 

 

 

 

 

 

 

 

L 

L 

5.2.2. -  WORK MODE CONFIGURATION: MODE 2- METER IMM.

 

To access the Work Mode, press

:

 

 

Steps to follow

:

 

 

 

 Access to the configuration menu. 

 
 

 

Move  the  cursor 

to the desired work 

configuration: 

(METER IMM).

 

 

     

        

+ 

 

Move  

Confirm 

 

 

Move the cursor and confirm the desired 
measurement units: 

(L)

 

     

         

+ 

 

Move  

Confirm 

 

 
 
 
 
 
 

Save the programmed values. 

 

 

5.2.2.1. - VOLUME OF TREATED WATER CONFIGURATION: 

MODE 2 - METER IMM.

 

 

To access the Work Mode, press

:

 

 

              

Steps to follow

:

 

 
 
 
 

L

 

Access to the configuration menu. 

 

 Move  the  cursor  to  set  the  volume  of 
water  that  can  be  treated  by  the 
softener’s resin bed. 

    

          

+ 

 

Move 

Increase value 

SEE THE TABLE ATTACHED TO SET THE 
LITRES OF TREATED WATER.

 

 

 

 

Save the programmed values. 

Summary of Contents for D-DF Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands