manualshive.com logo in svg

Curve D-DF Series, Instruction, Operation And Maintenance Manual

Share
Download
Curve D-DF Series Instruction, Operation And Maintenance Manual Download Page 11

11

 

ref: MA-ED-0008-EN-V16.0-MIÑO DESCALCIFICADOR D-DF-M3 & D-UF-M3.pdf 

 

 

 

 

 

 

 

 

 

+ 

5.2.1. - WORK MODE CONFIGURACION DEL: MODE 1 - TIMED.

 

To access the Work Mode, press: 

                     

Steps to follow: 

 

 

Access to the configuration menu. 

 

 
 
 
 

Move  the  cursor 

to the desired work 

configuration: 

(TIME).

 

 

      

        

+ 

 

Move  

Confirm 

 

 

Save the programmed values. 

 

 
 
 
 
 
 

5.2.1.1-  TIMED CONFIGURATION & INTERVAL BETWEEN REGENERACIONS: 

MODE 1 - TIMED

 

To access the Work Mode, press: 

                                      

Steps to follow: 

 
 
 

 

 Access to the configuration menu. 

 

 

Move  the  cursor 

to the desired 

regeneration time. 

 

     

        

+ 

 

Move 

Increase 

value 

 

 

Move the cursor to set the number of 
days between regenerations.  

 

 

    

 

Move 

 

Increase 

value 

 

 

 Save the programmed values. 

Summary of Contents for D-DF Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands