manualshive.com logo in svg

Curtiss-Wright DTI-VME/S, User Manual

Share
Download
Curtiss-Wright DTI-VME/S User Manual Download Page 52

INTERRUPTS 

 

Tail Pointer 
The Tail Pointer contains the address of the next standard priority interrupt entry in the 
queue.  That address does not have to be the next contiguous address. 
 

4.5 Operational Interrupt Registers 

Six Operational Interrupt Registers control interrupt processing and are discussed on the 
following pages.  (See the Registers section of this manual for more information.) 
 

4.5.1  Interrupt Queue Pointer Register 06 

The onboard RAM starting address of the standard priority interrupt queue is specified in the 
Interrupt Queue Pointer.  As interrupt entries are added to the queue, the contents of this 
register are updated with the address of the next entry in the queue. 
 

4.5.2  High Priority Interrupt Enable Register 07 

The High Priority Interrupt Enable Register allows you to select up to nine events to be 
enabled for high priority system handling.  When you enable an event as high priority, the 
host is notified each time the event occurs.   
 
To enable a particular event for high priority interrupt handling, set the corresponding bit to 
1.  Setting Bit 0 to 1 enables all standard interrupts to notify the host.  See page 3-8 for a bit 
explanation of this register. 
 
 

        

MSB

 

LSB

 

15 

14 13 

12 11 10 9 8 7 6 5 4 3 2 1 0 

DMA

ERR 

CMD

ERR 

DYN
BUS 

SS

FAIL 

END

BIT 

BIT 

FAIL 

EOL MSG

ERR 

STD

INT 

X X X X X X X 1 1 1 1 1 1 1 1 1 

 

Reserved 

 

 

Copyright 2004 

4-4 

DTI-VME/S 

 

Summary of Contents for DTI-VME/S

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands