background image

6. CONTROL  PANEL  OPERATION

13

6

.

2

 

 POWER/MODE

Pressing [<] returns you to the DDS screen. 

[POWER] button changes the operating modes of your

wered on the factory setting is in AUTO as shown to the right.

Pressing [<] returns you to the DDS screen.

Press [OK] to enter POWER/MODE. 
Pressing [OK] enters the display shown to the right and pressing the [+] or 

Pressing [OK] saves the required mode and returns to the previous screen. 

Pressing [POWER] to ON will display the screen as seen to the right. 

Pressing [OK] from the DDS screen enters the MAIN MENU.

VAPURE VP-Series Salt Chlorinator. 
When pressed the Mode will change AUTO to OFF then ON.

Pressing [POWER] to OFF will display the screen as seen to the right

Pressing [+] takes you to the last menu and using the [-] or [OK

Pressing [+] 5 times above displays the display shown to the right.

Pressing [+] takes you to last menus. 

[-] allows you to adjust the POWER/MODE setting from AUTO to OFF to ON.

6.3  CHLOR BOOST

to operate for 8hrs and automatically sets the chlorine setting to 100%. 

Super-Chlorinate. The bottom line will alternate between "[CHLOR BOOST] to END" 

This allows for an injection of extra sanitising time, also know as Chlorine Boost or 

and the fault message if there is any fault during CHLOR BOOST.

T

wo digits 08

wn to the right.

Pressing [+] or [-] increases or decreases in increments of 01:00 hrs whilst running.

When completed the unit will return to the DDS screen in the last selected POWER/MODE state 
and the CHLOR BOOST LED goes OFF.

Pressing [ BOOST ] again allows you to exit the CHLOR BOOST screen and return to the DDS screen.

CHLOR BOOST can also be entered by pressing the [OK] button in MAIN MENU and scrolling to 
CHLOR BOOST.

BEFORE ENTERING CHLOR BOOST YOU MUST BE IN THE DDS SCREEN.

[ BOOST ] button sets your VAPURE VP-Series Salt Chlorinator and pump 

When in operation the LED will be on. After the set time it reverts back to last selected 
POWER/MODE unless ON then it reverts to AUTO. 

The unit automatically defaults to 08:00 hours of ON time and the timer starts counting down 
immediately. 

www.crystalas.com

65a010a5-6d71e2d3-6b3148b4-770d42ea

Summary of Contents for VAPURE





































Reviews: