manualshive.com logo in svg

Crestron UPX-2, Operation Manual

Share
Download
Crestron UPX-2 Operation Manual Download Page 96

Crestron 

UPX-2 

Universal Presentation Processor  

 

Problem Solving 

Troubleshooting 

The following table provides corrective action for possible trouble situations. If 
further assistance is required, please contact a Crestron customer service 
representative.  

UPX-2 Troubleshooting 

TROUBLE 

POSSIBLE 

CAUSE(S) 

CORRECTIVE ACTION 

UPX-2 is not receiving 

power. 

Verify power to unit. 

Incorrect 

firmware/software. 

Update firmware/software versions as 
per those listed in the “Specifications” 
section. 

Follow connection procedures in this 
guide and inspect connector pins.  

UPX-2 does not 

function. 

Incorrect cable 

connections. 

Verify RGB output cable connection to 
unit and video display, and correct USB 
port. 

Wrong VT Pro-e or 

SIMPL Windows

 

programs.  

Verify correct programs. 

VT Pro-e project not 

set up correctly. 

Verify proper video set up for each 
video window displayed. 

No video output 
displayed. 

DTT touchpanel 

incorrectly setup. 

Check DVI/VGA switch 
(should be in VGA position). 

UPX-2 does not boot 
properly. 

Incorrect cable 

connections. 

Verify horizontal/vertical BNC cable 
connections.  
Verify 15-pin cable connection. 

VT Pro-e project not 

set up correctly. 

Verify correct video effect selected for 
video window. 

Wrong source or video 
displayed. 

Wrong effect selected 

in “Video Properties”. 

Select correct effect in VT-Pro-e “Video 
Properties”. 

Video from RGB source 
is garbled or no output. 

Analog join value has 

been set. 

Change analog join corresponding to 
desired source. 

IP address not correct 

(LAN green and amber 
LEDs are off). 

Assign correct IP address to UPX-2. 

IP mask not correct 

(LAN green and amber 
LEDs are on). 

Assign correct IP mask. 

UPX-2 does not respond 
to ping command. 

PC and UPX-2 not on 

same subnet. 

Ensure that the PC and the UPX-2 are 
on the same subnet. 

Mouse or touchpanel 
does not work. 

Incorrect Touch 

settings. 

Check Touch settings. 

DTT-15V2 does not 
respond to pen input. 

Power is cycled too 

quickly. 

Turn off DTT-15V2 for two seconds and 
restart. 

(Continued on following page) 

74  

¥

 Universal Presentation Processor: UPX-2 

Operations Guide – DOC. 6276B 

Summary of Contents for UPX-2



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands