Crane PROSSER STANDARD-LINE 9-81000 Series Installation And Operation Manual Download Page 29

Page: 29 / 31

230, 460, 575 Volt, Three Phase Control Panel Schematics

PARTS LIST

QTY

PART NO.

DESCRIPTION

2-210002-59

Flat Washer, 1/4” Stainless

2-23021-76

HxHd Screw, 1/4-20 x 1.37” lg SS

9-500520

Zinc Anode Sensor

1. Pump must be ordered with the Galvanic Protection Kit to

have the correct frame and outer shell.

2. Align two clearance holes in outer shell with the two drilled

and tapped holes in frame, before tightening cap screws

on the suction nozzle.

3. Fill the two drilled & tapped holes in frame approximately

half full of electrical bounding grease part number

2-45003-1.

4. Install washers and capscrews though zinc anode and into

the frame holes, partially filled with bonding grease and

tighten securely.

5. Route wire from anode to the suction nozzle. Loosen

suction nozzle capscrew & washer and install wire

between washer & suction nozzle, retighten capscrew.

Route other wire to discharge head and install under

discharge head capscrew and washer.

6. Slip suction strainer on pump, align mounting screws, mark

strainer where anode wire passes between suction nozzle

and strainer. Grind a notch in the strainer to allow

clearance for the wire. Install the strainer.

FIGURE 20

Galvanic Protection Kit P/N: 9-840572

Summary of Contents for PROSSER STANDARD-LINE 9-81000 Series
































Search results

Summary of Contents for PROSSER STANDARD-LINE 9-81000 Series

Reviews:

Related manuals for PROSSER STANDARD-LINE 9-81000 Series

Brands by name

Popular brands

Crane PROSSER STANDARD-LINE 9-81000 Series, Installation And Operation Manual

Search results

Summary of Contents for PROSSER STANDARD-LINE 9-81000 Series

Reviews:

Related manuals for PROSSER STANDARD-LINE 9-81000 Series

Brands by name

Popular brands