Crane PROSSER STANDARD-LINE 9-81000 Series Installation And Operation Manual Download Page 1

Page: 1 / 31

A Crane Co. Company

PROSSER

INSTALLATION and OPERATION MANUAL

STANDARD-LINE® Submersible Dewatering Pumps

IMPORTANT!

Read all instructions in this manual before operating pump.

As a result of Crane Pumps & Systems, Inc., constant product improvement program,

product changes may occur. As such Crane Pumps & Systems reserves the right to

change product without prior written notification.

420 Third Street

83 West Drive, Bramton

Piqua, Ohio 45356

Ontario, Canada L6T 2J6

Phone: (937) 778-8947

Phone: (905) 457-6223

Fax: (937) 773-7157

Fax: (905) 457-2650

www.cranepumps.com

Form No. 096928-Rev. Y

Series: 9-81000, 9-81500

9-82500,

9-85000

10HP thru 50HP, 3450RPM

SOME MODELS MAY NOT BE

AVAILABLE

Summary of Contents for PROSSER STANDARD-LINE 9-81000 Series
































Search results

Summary of Contents for PROSSER STANDARD-LINE 9-81000 Series

Reviews:

Related manuals for PROSSER STANDARD-LINE 9-81000 Series

Brands by name

Popular brands

Crane PROSSER STANDARD-LINE 9-81000 Series, Installation And Operation Manual

Search results

Summary of Contents for PROSSER STANDARD-LINE 9-81000 Series

Reviews:

Related manuals for PROSSER STANDARD-LINE 9-81000 Series

Brands by name

Popular brands