manualshive.com logo in svg

Crane Merchandising Systems Genesis, Technical Manual

Share
Download
Crane Merchandising Systems Genesis Technical Manual Download Page 13

2.4 Commissioning Procedure

The following procedure must be carried out by a trained installation engineer before
the machine can be used for the first time.

1.

Ensure that the electrical and water services to the machine are connected
correctly and turned on. Ensure that the waste tray is fitted correctly to the
machine. Open the front door of the machine and swing the cup turret assembly
out of the machine.

2.

Rotate canister outlets to upright position and remove the ingredient canisters -
DO NOT place ingredient canisters on the floor. Remove the lids from the
ingredient canisters.

Fill the canisters with the correct ingredients, re-fit the lids and re-fit canisters into
machine ensuring that they are returned to their correct positions. Rotate the
canister outlets to their correct operating positions.

Freshbrew Models: Fill freshbrew ingredient canisters with freshbrew tea and
coffee ingredient and refit to machine.

3.

Load the cup turret. Fill the tubes with the correct size cups for the type of cup
catcher fitted to the machine.Allow the cups to drop into
the tubes directly from the packaging. DO NOT TOUCH
THE CUPS WITH YOUR HANDS.

Important: Do not fill the tube directly above the cup
dispense position. Allow the cup turret motor to rotate a
full tube to the cup dispense position. Rotating the cup
turret by hand will damage the mechanism.

Note: If paper cups are being loaded, each pack of cups must first be inspected
for damage to the cup rims. Discard top cup from each stack. Damaged cups must
not be used.

4.

Swing the cup turret assembly back to its operating position. Ensure that the unit
is held securely by the magnetic catch.

5.

Insert the safety key (a) supplied with the machine into the
door switch as shown.The machine is now on.The water
inlet valve will open and the heater tank will start to fill.
The cup turret mechanism will index the first available full
cup stack to the dispense position and drop the cup stack
into the cup drop mechanism. Fill the remaining empty cup
stack with cups.

11

Technical Manual

Summary of Contents for Genesis

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands