background image

4-44

Section 4

Correct Craft, Inc.

Optional Equipment

Stereo and Speaker Pods

All Nautiques are stereo ready and include an iPod

TM

/MP3 Port.

They have been pre-wired for your Correct Craft Dealer to install a
stereo. Limited and Team Edition Nautiques come with a Clarion
stereo with Polk/MOMO speakers. Deafcon I or Deafcon III;
speakers can be purchased as an option (206 and 216 only).
Correct Craft mounts all of its stereos in the glove box on the dash.
A digital remote control can be mounted on the lower left side of
the dash pod. The digital remote control displays all necessary
control functions at your fingertip. Consult your Correct Craft
Dealer for the stereo configuration for your boat.

Ballast Tanks (216)

The tank increases the wake for trick skiing, making your Sport
Nautique the most versatile water sports tow package in the world. 

Ballast Tank Control Switches

Press the button for the ballast tank you choose to fill or drain.

To fill: 

Press and release quickly; the LED will illuminate and the

pump will begin to fill the tank. Press the button again to stop the
pump. Use the tank gauge to measure the level of water in the tank.

If you continue to fill the tank beyond its capacity, the excess water
will expel from the tank vent. The pump will continue to operate
for approximately 10 minutes if the pump is left in the fill mode,
then shut off.

To drain: 

Press and hold the button until the LED begins to flash

and the pump will begin to drain the tank. Press the button again
to stop the pump.

The pump will stop pumping when the tank sensor senses the “No
Water Level” in the tank. The LED will continue to flash for
approximately 10 minutes unless the button is pressed again.

Nautique Ski Sec 4.qxd:Nautique Ski Sec 4.qxd  6/19/07  4:44 AM  Page 44

Summary of Contents for 2008 2008 70141





























































































































































































Reviews: