manualshive.com logo in svg

CORRECT CRAFT 2008 2008 70141, Owner'S Manual

Share
Download
CORRECT CRAFT 2008 2008 70141 Owner'S Manual Download Page 134

6-10

Section 6

Correct Craft, Inc.

In order to prevent personal injury to you or others, the engine
cover must be closed whenever the engine is running.

• DO NOT operate the engine with the engine cover open or

while someone is in the area of an open engine cover.

• DO NOT open the engine cover unless the engine is turned

OFF and rotating parts are stationary and remain in a
stationary position.

IT IS RECOMMENDED THAT ALL WORK ON THE ENGINE BE
DONE BY TRAINED AND QUALIFIED SERVICE PERSONNEL.

During the warm up period, check the gauges for correct and
normal operation of all the systems: 

• Oil pressure 35-80 psi, approximately at 2000 rpm
• Cooling water flow and water temperature 140-170°
• Cooling water temperature for fresh water systems: 170-210°
• Volts should rise to around 13-14V or higher
• Idle rpm (600-700) in gear

DO NOT operate at high rpms in NEUTRAL.

DO NOT shift into forward or reverse at engine speeds
above idle rpms. 

DO NOT operate the engine without a cooling water
supply. 

Damage to the water pump impeller and engine can
occur. If the engine does not start, refer to Section 9,
Troubleshooting.

CAUTION

Nautique Ski Sec 6.qxd:Nautique Ski Sec 6.qxd  6/19/07  4:49 AM  Page 6-10

Summary of Contents for 2008 2008 70141





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands