CORRECT CRAFT 2008 2008 70141 Owner'S Manual Download Page 155 | Manualshive

Page: 155 / 188

background image

8-9

Quick Oil Drain System

Change the engine oil after the first 25 hours of operation, then
after every 50 hours. The boat must be removed from the water to
use the quick oil drain system. There is a drain hose attached to the
bottom of the oil pan with a small plug screwed into the loose end
of the hose.

Remove the bilge drain plug and put the end of the drain hose
through the bilge drain opening. Make sure there are no kinks or
sharp bends in the hose. The engine will drain most efficiently
when the oil is warm. Allow several minutes for the oil to settle and
drain. Dispose of used oil in an environmentally safe manner.

NOTICE

Be sure the engine is off when you are draining your oil.

CORC169

Care and Maintenance

Prolonged or repeated contact with used

engine oil can cause death or serious injury. Wash
affected area immediately with soap and water.

!

WARNING

Nautique Ski Sec 8.qxd:Nautique Ski Sec 8.qxd 6/18/07 5:18 AM Page 8-9

«
...
153
154
155
156
157
...
»

Summary of Contents for 2008 2008 70141





























































































































































































Reviews:

No comments

Related manuals for 2008 2008 70141

ALL-STAR 2101112

Brand: O'Brien Pages: 8

Brand: Bestway Pages: 6

HYDRO-FORCE 65023

Brand: Bestway Pages: 36

Brand: Bestway Pages: 44

Brand: Hobie Pages: 26

Brand: Laser Performance Pages: 11

Quicksilver 200 Tendy Slatted

Brand: Mercury Pages: 63

Brand: Walker Bay Pages: 4

Brand: Sailfish Pages: 43

Cap Camarat 625

Brand: Jeanneau Pages: 54

SUN ODYSSEY 50DS

Brand: Jeanneau Pages: 156

Brand: Intex Pages: 13

Brand: Quicksilver Pages: 53

FX High Output WaveRunner 2008

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 134

GP1300R WaveRunner 2008

Brand: Yamaha Pages: 98

Brand: Quicksilver Pages: 47

Brand: Lalizas Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands