CORRECT CRAFT 2008 2008 70141 Owner'S Manual Download Page 12

Page: 12 / 188

Correct Craft, Inc.

1-2

• DO NOT operate the boat while under the influence of

alcohol or other drugs.

• DO NOT stand or allow passengers to stand in the boat, or

sit on the transom, seat backs, engine cover or sides of the
boat while the engine is running. You or others may be
thrown from the boat.

• DO NOT allow any type of spark or open flame on board. It

may result in fire or explosion.

• DO NOT leave children in the boat without adult

supervision.

• DO NOT sit in front of the operator to avoid obstructing the

operator’s view.

• DO NOT dive from the boat without being absolutely sure

of the depth of the water, otherwise severe injury or death
may occur from striking the bottom or submerged objects.

• DO NOT swim near the boat when the engine is running.

Being in NEUTRAL is not enough, the propeller may still be
turning and carbon monoxide may be present.

• DO NOT replace your boat’s marine parts with automotive

parts.

• DO NOT remove or modify any components of the fuel

system except for maintenance by qualified personnel.
Tampering with fuel components may cause a hazardous
condition.

• DO NOT wrap ski lines or mooring lines around any body

part which may become entangled in the line if you fall
overboard and the boat is moving.

• Keep track of ski lines and dock lines so they do not become

entangled in the propeller.

• Be sure to securely attach the engine Emergency Stop switch

lanyard to a part of your clothing, such as a belt loop, when
operating the boat.

• Be sure to keep a watch for other boats, swimmers and

obstructions in the water. Stay away from other boats and
personal watercraft.

• Be sure to have an experienced operator at the helm and

always have at least three people present for safe towing –
one to drive, one to observe and one to ski or ride.

Section 1

Nautique Ski Sec 1.qxd:Nautique Ski Sec 1.qxd 6/19/07 4:38 AM Page 1-2

Summary of Contents for 2008 2008 70141





























































































































































































Search results

Summary of Contents for 2008 2008 70141

Reviews:

Related manuals for 2008 2008 70141

Brands by name

Popular brands

CORRECT CRAFT 2008 2008 70141, Owner'S Manual

Search results

Summary of Contents for 2008 2008 70141

Reviews:

Related manuals for 2008 2008 70141

Brands by name

Popular brands