manualshive.com logo in svg

CORRECT CRAFT 2008 2008 70141, Owner'S Manual

Share
Download
CORRECT CRAFT 2008 2008 70141 Owner'S Manual Download Page 112

4-42

Section 4

Correct Craft, Inc.

Engine Cooling Water Intake Valve

Your boat is equipped with a valve (seacock) on the engine cooling
water intake. The handle has a slide mechanism to prevent the
valve from being shut off inadvertently. The valve is used to shut off
the water supply in the event a hose failure or water leakage occurs.
The valve is open when the yellow handle is in-line with the valve
body and the valve is closed when the handle is perpendicular to
the valve body. Leave the valve open at all times unless an
emergency condition requires you to close the valve to stop a leak
or the possibility of a leak. The valve is located on the starboard side
of the transmission.

CORC067

OFF

ON

RAW WATER

S

TRAINER

WATER
VALVE

Nautique Ski Sec 4.qxd:Nautique Ski Sec 4.qxd  6/19/07  4:44 AM  Page 42

Summary of Contents for 2008 2008 70141





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands