Coretec VCX-7401 Installation And Operating Instructions Manual Download Page 25 | Manualshive

Page: 25 / 38

background image

DEATHBLOW

This command causes a reboot of the device. The purpose of this command is to

cause a reboot from the password prompt. If you cannot login into the command, prompt
because of the “Another administrator is logged in.” message, then you can use
DEATHBLOW as the password to return the unit to the power up state.

EXIT

Exits from the command prompt and releases the current login. You may also

use the following alternatives… LO (Log Off) and QUIT.

NTSC

This command sets unit for NTSC video operation.

PAL

This command sets unit for PAL video operation.

REBOOT

This command restarts device from power-up state. Most changes in device

settings require a reboot after a commit.

START

This command starts encoding or playback (video out).

STOP

This command stops encoding or playback (video out).

VER

This command displays the software version/build date, BSP (board support

package) version/build date, and board revision.

Example response:

Version: VCX7401 v1.6a, Date: 29JUN11

25

«
...
23
24
25
26
27
...
»

Summary of Contents for VCX-7401







































Reviews:

No comments

Related manuals for VCX-7401

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 30

Brand: Yamaha Pages: 30

Brand: Yamaha Pages: 56

EF4500iSE - Inverter Generator

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 20

RX-Z11 - AV Receiver

Brand: Yamaha Pages: 4

Brand: ATEN Pages: 2

Brand: HIKVISION Pages: 50

Giga-McBasic-II

Brand: B&B Electronics Pages: 14

Brand: VigilLink Pages: 6

Brand: Tvone Pages: 16

Brand: PRO SIGNAL Pages: 2

Indigo ADDEC-210

Brand: Crystal Vision Pages: 37

Brand: Kostal Pages: 12

Brand: SKP Pro Audio Pages: 20

Brand: Ensemble Designs Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands