Coretec VCX-7401 Installation And Operating Instructions Manual Download Page 21 | Manualshive

Page: 21 / 38

background image

Miscallaneous Tab

Logout Button

The logout button will log the user out with out commiting any changes

that may have been made during the current session. Any changes that were made
will stay until the device has been rebooted.

Commit Button

The commit button will commit any changes that may have been

configured in the current seesion. If you reboot after pressing the commit button,
then all changes will be commited and saved and viewable upon reboot.

Commit/Reboot Button

The commit/reboot button will also log out the user and also commit any

changes that may have been configured in the current seesion. This means that
when the devices shuts down and reboot the changes that were made will still be
in effect.

21

«
...
19
20
21
22
23
...
»

Summary of Contents for VCX-7401







































Reviews:

No comments

Related manuals for VCX-7401

Brand: ABB Pages: 10

Brand: Ramsey Electronics Pages: 20

Brand: Panasonic Pages: 2

NDS NETWORK AUDIO PLAYER

Brand: NAIM Pages: 23

Brand: NAIM Pages: 36

Brand: NAIM Pages: 22

Brand: NAIM Pages: 8

HDX - REMOTE CONTROL CODE

Brand: NAIM Pages: 32

Brand: NAIM Pages: 2

Brand: NAIM Pages: 17

HDX - REMOTE CONTROL CODE

Brand: NAIM Pages: 8

Brand: Velux Pages: 10

Brand: ZIEHL-ABEGG Pages: 26

Brand: Broadcast Tools Pages: 10

Brand: ADS Technologies Pages: 6

IMP-C1000-SFP-bt-24 Series

Brand: ANTAIRA Pages: 2

Brand: Inter-m Pages: 28

Brand: Cerwin-Vega Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands