manualshive.com logo in svg

Coretec VCX-7401, Installation And Operating Instructions Manual

Share
Download
Coretec VCX-7401 Installation And Operating Instructions Manual Download Page 34

Video Output (NTSC/PAL)

Impedance:

75 ohm unbalanced, return loss > 30 dB

Output Level: 1.0 volts peak to peak nominal 
 (.9 volts minimum to 1.1 volts maximum)

Sync Level:

257 mV (36 IRE) to 314 mV (44 IRE)

Bar Level:

642 mV (90 IRE) to 785 mV (110 IRE)

Burst Level: 257 mV (36 IRE) to 314 mV (44 IRE)

Resolution:

Full D1: 720h x 480v (NTSC); 720h x 576v (PAL)

1/2 D1:  352h x 480v (NTSC); 480h x 576v (PAL)
CIF:

  352h x 240v (NTSC); 352h x 288v (PAL)

QCIF:   160x120
QQCIF: 80x60

Frame Rate: 1 to 30 frames per second maximum

Data (Network)

Format:

Ethernet IEEE 802.3; 10/100 Base T

Line Rate:

down to 64kbps

Data (Sub-channels)

Format:

RS-232 or RS-422 (programmable)          (2)

Data Rates:

2400, 4800, 9600, 19200, 38400 bps

Programming Data

Format:

EIA RS-232C  (primary data lines)

Rate:

38.4 kbps

Form:

8-bit data, 1 stop bit, no parity

34

Summary of Contents for VCX-7401







































Reviews:

No comments

Brands by name

Popular brands

Load more brands