manualshive.com logo in svg

Coretec VCX-7401, Installation And Operating Instructions Manual

Share
Download
Coretec VCX-7401 Installation And Operating Instructions Manual Download Page 12

On the top of the screen is a front view image of the device. If you click on any of 

these ports the associated tab will appear below the image inside the tabbed pane. 
Also an animation will appear for a few seconds on the bottom right corner. The user 
may click here in order to to be sent to tutorial page. The user will find here, all the 
associated documents to the VCX-7401, such as the manual, as well as video tutorials 
on how to use the device and the web applet. Aside from clicking on the ports inteh 
image of the device at the top of the applet, they can click directly on the tabs below. 
There are currently nine tabs to choose from: Main, Network, Subchannel, OSD, 
Video, MPEG4, H264, Decoder and Miscallaneous. To the right the user will see 7 
buttons: Logout, Commit, Commit/Reboot, Reboot, Open Manual and two other 
buttons that allow you to view either the H264 or MPEG4 video stream on a new web 
page.

12

Summary of Contents for VCX-7401







































Reviews:

No comments

Brands by name

Popular brands

Load more brands