background image

21

WARRANTY NOTICE

Cooke Industries will provide a new or repaired part or component at its discretion in place 

of any part or component, which is found upon inspection, to be defective in material or 

workmanship during the warranty period.

Said part or component will be repaired or replaced without charge to the initial user  

during normal working hours at the place of business of Cooke Industries or a Cooke 

Industries nominated distributor upon the consent of Cooke Industries.

This warranty does not apply to failure occurring as a result of abuse, misuse, negligent 

installation or repair and/or alterations or modifications whatsoever made to the  

product without the express written consent of Cooke Industries. This also extends to 

outside influences or site conditions which may impede or obstruct the correct functioning 

of the unit.

Warranty claims are to be lodged at 

www.cookeindustries.com.au/warranty

Please note the user must submit the serial number and proof of purchase to make a claim 

under this warranty.

SPECIAL CONDITIONS

1.

  Onsite labour, service call or freight charges to return items to Cooke Industries are the 

responsibility of the purchaser.

2.

  Under no circumstances whatsoever shall Cooke Industries be liable for incidental or 

consequential damages, inconveniences or expenses in connection with the removal or 

replacement of this product.

3.

  In circumstances whereby it has been deemed that the installer has clearly not followed 

the steps and information as set out in this guide (negligent installation), the warranty 

will become null and void.

4.

  Under no circumstances will Cooke Industries be liable for damage caused to persons 

or property as a result of the incorrect installation or misuse of this product.

Summary of Contents for WaterWitch

























Reviews: