background image

“STATUS WORD” parameter STA60M

VALUE

CONFIGURATION

16

Temperature display in “big area” and all enabled with Set settable 10-35 °C

17

Temperature display in “big area” and FAN key “disabled” with Set settable 10-35 °C

18

Temperature display in “big area” and CLOCK key “disabled” with Set settable 10-35 °C

19

Display Set in “big area” and all enabled with Set adjustable from 10 to 35 °C

20

Display Set in “big area” and and FAN key “disabled” with Set adjustable from 10 to 35 °C

21

Display Set in “big area” and CLOCK key “disabled” with Set settable 10-35 °C

22

Temperature display in “big area” and all enabled with Set adju - X (X defined by configurator X maximum 5 °C).

23

Temperature display in “big area” and FAN key “disabled” with Set adju - X (X defined by configurator X 

maximum 5 °C).

24

Temperature display in “big area” and CLOCK key “disabled” with Set adju - X (X defined by configurator X 

maximum 5 °C).

“STATUS WORD” parameter STA70M

VALUE

CONFIGURAZIONE

32

Temperature display

33

Setpoint display

“STATUS WORD” parameter NR9001

BIT

Description

“0”

“1”

Default

0

Operation Mode

Remote (Disable digital input Comfort/

Economy and Power Off)

Local (Enable digital input Comfort/

Economy and Power Off)

0

1

Ambient Temperature

Remote (comes from STA60M or 

STA70M)

Local (comes from “dedicated” 

analogue input S1)

0

2

Summer / Winter Changeover

Remote (Disable digital input Summer/

Winter DI3)

Local (Enable digital input Summer/

Winter DI3)

1

3

Temperature Set 

Remote (comes from NR9000-RT)

Local (comes from “dedicated” 

analogue input S2)

0

4

Window Contact

Disable digital input DI1

Enable digital input DI1

0

5

Temperature Set Correction Mode

10-35 °C

±3K

0

6

DIP switch 

Enable

Disable

0

7

Electrical Battery

Disable

Enable 

0

Functions STA60M sensors

Through STA60M sensor the user is able to:

• 

set regulation setpoint;

• 

set the operating mode;

• 

set fan speeds;

• 

set time tables;

• 

set Modbus communication parameters as baud rate and Modbus address. 

Functions STA70M sensors

Through the STA70M sensor the user is able to:

• 

set regulation setpoint;

• 

set the operating mode;

• 

set fan speeds;

• 

set time tables;

• 

set Modbus communication parameters as baud rate and Modbus address.

1

st

 Issue

06/2019

DBL585e

Page 16

Summary of Contents for Energon NR9001






















Reviews: