background image

13

W415-0318 / 03.05.09

3.3 GLOWING 

EMBERS

3.4 DOOR 

INSTALLATION

Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of 
logs (#2 & #3). Care should be taken to shred the embers into thin, small irregular pieces as only the exposed 
edges of the fi bre hairs will glow. 

The ember material will only glow when exposed to direct 

fl

 ame; how-

ever, care should be taken to not block the burner ports. 

Blocked burner ports can cause an incorrect fl ame pattern, carbon deposits and delayed ignition. PHAZER

TM

 

logs glow when exposed to direct fl ame. Use only certifi ed "glowing embers" and PHAZER

TM

 logs available 

from your Continental® dealer. 

FIGURE 3.4.1

3.4.1

      Insert the tool supplied (which is 

              located behind the left side trim) into 
              spring loaded door latch. 

3.4.2 

     Pull and turn the latch 90°.

3.4.3 

     Release the latch.

3.4.4 

     Tilt the top of the door forward until you 

              can grab the sides of the door. Lift up 
              and out of the bottom door retainer.

3.4.5

      To install, reverse the order of these 

              instructions.

FIGURE 3.4.2

FIGURE 3.4.3

FIGURE 3.4.4

!

WARNING

Glass may be hot, DO NOT touch glass until cooled.

The door latches are part of a safety system and must be properly engaged. Do not operate the 

fi

 replace 

with latches disengaged.

Do not strike, slam or scratch glass. Do not operate 

fi

 replace with glass removed, cracked, broken or 

scratched. 

Summary of Contents for CDI-44N





























Reviews: