Contex AA51A Operator'S Manual Download

Page: 43 / 125

Using the scanner, how do I …?

4-3

ATAC Key

Paper Ready Indicator

Paper Forward

Paper Reverse

Adjusting the insertion slot for thick media with ATAC:

1. Press the ATAC key on your iJET Panel to set the scanner in ATAC mode.

2. The

Paper Ready Indicator

blinks yellow indicating the scanner is in ATAC mode but not yet

ready, i.e., the pressure-platen is not yet positioned on the thick original.

3. Press and hold the

Paper Forward

key (arrow up) key to raise the pressure-platen until

there is room to insert the thick original.

4. Insert the thick original evenly for a straight scan path.

laten

til the

5. Press and hold the

Paper Reverse

(arrow down) key to lower the pressure-p

pressure-platen stops on its own.

6. The

Paper Ready

indicator will turn yellow (stop blinking) when the pressure-platen is

positioned correctly and is ready for thick media scanning.

Summary of Contents for AA51A






























































































































Search results

Summary of Contents for AA51A

Reviews:

Related manuals for AA51A

Brands by name

Popular brands

Contex AA51A, Operator'S Manual

Search results

Summary of Contents for AA51A

Reviews:

Related manuals for AA51A

Brands by name

Popular brands