background image

www.conquerordoors.com

                                                 

 

1.

 

Required tool list   

 
This automatic door opener is designed to be installed by trained professionals. 
If  this  is  to  be  installed  as  a  DIY  install,  you  will  require  all,  but  not  limited  to,  the 
following; 

 

Electric Drill or Battery Drill   

 

Timber Tec Driver Bit 

 

Socket Set 

 

Philips and Flat Screw Drivers 

 

Silicon Spray 

 

Builders Pencil   

 
2.

 

Important safety instructions 

 
WARNING – INCORRECT INSTALLATION CAN LEAD TO SEVER INJURY 
FOLLOW ALL INSTALLATION INSTRUCTIONS IN THIS MANUAL AND 
ALWAYS DO THE FOLLOWING: 

 
1)

 

Your  garage  doors  need  to  be  kept  properly  balanced  and  in  a  mechanically  sound 
condition.  Have  a  professional  service  person  make  repairs  to  cables,  spring  assemblies 
and other hardware, and to ensure that the door is serviced on a regular basis. 

2)

 

Do not let children play near a garage door when it is opening or closing. Never operate 
the door without being able to see it through the entire operation 

3)

 

Never  put  fingers  between  the  sections  of  a  garage  door,  even  if  you  own  a  Conqueror 
Pinch Free Sectional Door, best practice is always to keep your fingers away from moving 
parts. Keep hands and fingers clear of section joints, hinges, tracks, springs and other door 
parts. 

4)

 

Do not let children play with transmitters or remote controls, and place these items out of 
reach of children. 

5)

 

Test  the  door  operator  automatically  reverses  on  hitting  an  obstruction  monthly.  The 
garage  door  MUST  reverse  on contact  with a  40mm high  object  (or  a 50mm  by  100mm 
board laid flat) on the floor. If the garage door does not reverse, adjust either the force or 
the limit of travel, and re-test the automatic reversing function.   

6)

 

Disconnect  the  electrical  power  to  the  operator  before  attempting  any  repairs.  Only 
authorized  repair  and  service  agents  are  permitted  to  remove  the  outer  cover  of  the  auto 
opener. Only simple repairs to the opener or door should ever be carried out. If in doubt, 
call a Conqueror service agent immediately. 

7)

 

If  possible,  use  the  emergency  release  only  when  the  door  is  closed,  as  should  the  door 
have  lost  spring  tension  or  the  cable  had  come  off,  this  may  result  in  the  door  falling 
rapidly which can cause serious injury or death. 

8)

 

Do not use the emergency release rope to open or close the door! 

9)

 

Keep this manual in a safe place along with a copy of the invoice. 

 

 

 

Summary of Contents for CIL-BD800S















Reviews: