Congatec COM Express conga-TR3 User Manual Download Page 83

Page: 83 / 105

2016

congatec

TR33m10

83/105

Feature

Options

Description

Isolate SMBus Segments

Never
During POST

Always

Allows isolation of off-module SMBus from internal SMBus.

11.3.11 SATA Submenu

Feature

Options

Description

SATA Controller

Disabled

Enabled

Enable or disable the onboard SATA controller.

SATA Mode Selection

Legacy IDE
Native IDE

AHCI

Select onboard SATA controller mode. Select legacy IDE mode if your OS doesn’t allow interrupt
sharing.

SATA Hot-Removal Support

Disabled

Enabled

Enable or disable hot removal of SATA devices (AHCI mode only)

SATA Port 0 State

Enabled

Disabled

Enable or disable SATA port 0.

Speed Limit

Auto

Gen1
Gen2

Select max. SATA speed generation for the selected port.
Auto = up to Gen3

ESATA Support

Disabled

Enabled

Enabled or disable ESATA and hotplug (AHCI mode only) support.

SATA Port 1 State

Enabled

Disabled

Enable or disable SATA port 1.

Speed Limit

Auto

Gen1
Gen2

Select max. SATA speed generation for the selected port.
Auto = up to Gen3

ESATA Support

Disabled

Enabled

Enabled or disable ESATA and hotplug (AHCI mode only) support.

SATA Port 0

No option

SATA drive 0 information.

SATA Port 1

No option

SATA drive 1 information.

11.3.12 ACPI Submenu

Feature

Options

Description

Hibernation Support

Disabled

Enabled

Enable or disable system ability to hibernate (operating system S4 sleep state). This
option may not be effective with some operating systems.

Summary of Contents for COM Express conga-TR3








































































































Search results

Summary of Contents for COM Express conga-TR3

Reviews:

Related manuals for COM Express conga-TR3

Brands by name

Popular brands

Congatec COM Express conga-TR3, User Manual

Search results

Summary of Contents for COM Express conga-TR3

Reviews:

Related manuals for COM Express conga-TR3

Brands by name

Popular brands