manualshive.com logo in svg

Congatec COM Express conga-TR3, User Manual

Share
Download
Congatec COM Express conga-TR3 User Manual Download Page 13

Copyright 

© 

2016 

congatec 

AG 

 

      TR33m10 

 

      

13/105

2.2 

Supported Operating Systems

The conga-TR3 supports the following operating systems.

 

•

Microsoft

®

 Windows

®

 10

 

•

Microsoft

®

 Windows

®

 10 IOT enterprise

 

•

Microsoft

®

 Windows

®

 8.1

 

•

Microsoft

®

 Windows

®

 8.1 Embedded Standard

 

•

Microsoft

®

 Windows

®

 7

 

•

Microsoft

®

 Windows

®

 7 Embedded Standard 

 

•

Linux

 

Note

To improve the graphic performance of conga-TR3 after installing Microsoft

®

 Windows

®

 Operating System, congatec AG recommends the 

installation of AMD catalyst driver.

2.3 

Mechanical Dimensions

 

•

95.0 mm x 125.0 mm (3.74” x 4.92”)

 

•

Height approximately 18 or 21mm (including heatspreader) depending on the carrier board connector that is used. If the 5mm (height) 
carrier board connector is used then approximate overall height is 18mm. If the 8mm (height) carrier board connector is used then approximate 
overall height is 21mm.

Summary of Contents for COM Express conga-TR3










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands