background image

Place one of the 

deck connectors 

[F] over the upper 

handrail post and 

slide down.  Check 

to make sure side 

marked [This Side 

down] is  

facing downward. 

Repeat to install the  

second part [F] 

Step 15

To install the upper 

handrail posts [E] first 

locate the openings 

on panel [A]  marked 

with #3. Next insert 

the tabs on part [E] all 

the way into the open-

ings then tap down 

with a rubber mallet 

until seated. Repeat 

to install the other 

part [E].

Step 13

The top tread [I-3] will 

install slightly differ-

ent than the previous 

two. Install this tread 

by placing over the 

four tabs located on 

side panels [A]. Using 

a rubber mallet strike 

the top of the tread 

directly over the tabs 

until seated.

Step 14

With the step in place and positioned about 

1 inch away from inside of pool wall [

back 

of step must not touch pool liner

] extend the two deck con-

nectors onto the pool deck and attach to the handrail posts 

using 2- #10 x 1-1/4” screws through the deck connectors 

and into the posts. If you have a wood deck attach the deck 

connectors to the pool deck using 2-#10 x 1-1/4 screws  in 

each connector. If your pool deck is concrete consult with 

your local hardware store for the proper anchors and screws.

Step 18

Step 16 (Cont.)

Using a Phillips head screwdriver install one of the  

#10 x 1-1/4” stainless screws at each location [4 total].  

[HAND TIGHTEN ONLY]

With your Curve step fully 

assembled locate the [4] 

recessed screw locations on 

the top tread. With a cordless 

drill, at each of these [4]  

locations drill a 

small 1/8” pilot 

hole completely 

through the tread 

and into the  

sidewall below.

Step 16 (Cont.)

WARNING!

  

Using a corded drill near pool 

may result in electrocution.

With a helper place the pool step into 

swimming pool. 

WARNING! 

Pool step will be heavy. Have additional 

help. Do not attempt to place the step by yourself.

Hold the step under water at a slight angle until all the air 

bubbles stop. Tilt the step in the other direction until all the 

air bubbles stop. Be patient this process will take a few  

minutes.

 

If the pool step is still floating all of the air is not 

out. Lean step to the side again until air bubbles stop.

Step 17

4

Place handrails [G] 

over the top of hand-

rail posts, push down 

to lock in place.

Step 16

WARNING! 

DO NOT LIFT 

THE STEP BY 

HANDRAILS!

Summary of Contents for CCX-IG









Reviews: