Comtech EF Data MBT-5000 User'S Installation And Operation Manual Download Page 9

Page: 9 / 138

PREFACE

About this Manual

This manual provides installation and operation information for Comtech EF Data’s MBT-5000

L-Band Up/Down Converter System. This document is intended for the persons responsible for

the operation and maintenance of the MBT-5000.

Disclaimer

Comtech EF Data has reviewed this manual thoroughly in order to provide an easy-to-use guide to

this equipment. All statements, technical information, and recommendations in this manual and in

any guides or related documents are believed reliable, but the accuracy and completeness thereof

are not guaranteed or warranted, and they are not intended to be, nor should they be understood

to be, representations or warranties concerning the products described. Further, Comtech EF Data

reserves the right to make changes in the specifications of the products described in this manual at

any time without notice and without obligation to notify any person of such changes.

If there are any questions regarding this equipment or the information in this manual,

please contact Comtech EF Data Product Support.

Conventions and References

Patents and Trademarks

See all of Comtech EF Data's Patents and Patents Pending at http://patents.comtechefdata.com.

Comtech EF Data acknowledges that all trademarks are the property of the trademark owners.

Warnings, Cautions, and Notes

A WARNING informs you about a possible hazard that MAY CAUSE DEATH or

SERIOUS INJURY.

Summary of Contents for MBT-5000










































































































































Search results

Summary of Contents for MBT-5000

Reviews:

Brands by name

Popular brands

Comtech EF Data MBT-5000, User'S Installation And Operation Manual

Search results

Summary of Contents for MBT-5000

Reviews:

Brands by name

Popular brands