background image

TECHNICAL DATA

Technical data of the thermostats (transmitters):

— temperature measurement range:

    

5 to 35°C (in 0.1°C increments) 

— adjustable temperature range: 

 

5 to 35°C (in 0.5°C increments)

— temperature measurement accuracy:

 

±0.5°C

— temperature calibration range:

 

 

±3°C (in 0.1°C increments)

— selectable switching sensitivity:

    

±0.1°C; ±0.2°C; ±0.3°C

— storage temperature:

-10°C 

to 

+40°C

— battery voltage:

  

2 x 1.5V 

ALKALINE

 batteries

(LR6 

type; 

AA 

size)

— power consumption:

1.3mW

— battery lifetime: 

approx. 

year

— operating frequency:

868.35MHz

— dimensions:

 

 

130 x 80 x 22mm (without holder)

— weight:

112g

— temperature sensor type:

NTC 10kΩ ±1% at 25°C

Technical data of the receiver unit:

— power supply voltage:

230V 

AC, 

50Hz

— power consumption:

0.3W

— loadability of the relay that controls the boiler:

 

24V AC/DC to 230V AC, 50Hz,

6A 

(1A 

inductive 

load)

— voltage of the zone outputs: 

230V AC, 50Hz

— loadability of the zone outputs:

 

1A (0.5A inductive load)

— transmission distance:

   

approx. 50m in open terrain

— weight:

210g

Total weight of the device: approx. 550g (2 ther2 1 receiver)

- 19 -

Summary of Contents for Q8RF





















Reviews: