Compliance West HT-10KVDC Instruction Manual Download Page 3 | Manualshive

Page: 3 / 29

background image

Dear Customer:

Congratulations!  Compliance West USA is proud to present you
with your Dielectric Withstand Tester.  Your instrument features
a  groundbreaking  logic-controlled  circuit  design  and  ergonomic
front  panel,  and  represents  the  latest  in  high  voltage laboratory
testing.

To  fully  appreciate  all  the  features  of  your  new  meter,  we
suggest  that  you  take  a  few  moments  to  review  this  manual.
Compliance West USA stands by your instrument with a full one-
year warranty and a loaner instrument policy.  If the need arises,
please don't hesitate to call on us.

Thank you for your trust and confidence.

Rev 5.1, April 2009

«
1
2
3
4
5
...
»

Summary of Contents for HT-10KVDC






























Reviews:

No comments

Related manuals for HT-10KVDC

Brand: Omnia Pages: 8

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: Jacobs Ladder Pages: 16

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: Quadro mdb Pages: 4

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

Brand: xsto Pages: 76

Brand: F&V Pages: 5

Brand: F Care Systems Pages: 2

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Air 2000 Outdoor

Brand: ubbink Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands