CommScope Ruckus ICX 7750 Hardware Installation Manual Download Page 21

Page: 21 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

•

Shipping carton contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

•

Installation and safety considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

•

Installation tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

•

Installation precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

•

Installing the device in a rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

•

Two-post rack mount installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

•

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295). . . . . . . . . . . . . . . . . . . . . . . . 26

•

Grounding the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

•

Grounding the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

•

Powering on the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

•

Power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

•

Attaching a PC or terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

•

Connecting to the management port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

•

Installing an SFP+ or a QSFP+ transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

•

Connecting network devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

•

Stacking Ruckus ICX 7750 switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Shipping carton contents

Ruckus ICX 7750 devices ship with all of the following items included in the shipping carton. When unpacking the device, verify that the
contents of the shipping carton is complete, if any items are missing, contact the place of purchase.

•

The Ruckus ICX 7750 device

•

An accessory kit containing the following items:

•

Rack mounting kit containing two L-shaped mounting brackets and two sets of eight sink-head screws

•

Two-post rack kit containing four rack-mounting screws and four cage nuts

•

One grounding kit, containing one grounding lug and one grounding screw

•

Two Micro-HDMI to RJ45 stack control-path cables (currently not used)

•

One control-path cable holder kit, containing one cable holder and one screw

•

One console cable (Mini-USB to RJ45)

•

One RJ45-to-DB9 adapter

•

China ROHS sheet

•

Read Me First document

CAUTION

Procedures in this manual are intended for qualified service personnel.

Summary of Contents for Ruckus ICX 7750



























































































Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands

CommScope Ruckus ICX 7750, Hardware Installation Manual

Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands