manualshive.com logo in svg

CommScope Ruckus ICX 7750, Hardware Installation Manual

Share
Download
CommScope Ruckus ICX 7750 Hardware Installation Manual Download Page 19

Ruckus ICX 7750 Switch Hardware Installation Guide 

17

Part Number: 53-1003900-10

Ruckus ICX 7750 Overview

Supported transceivers and cables

 

The 40 GbE BiDi transceivers enable 40 GbE links to be supported on installed 10 GbE duplex fiber infrastructure. This optic has the 
same port limitations as the LR4 optic.

Breakout cables

The Ruckus ICX 7750 can support the following breakout cables on certain 40 GbE ports:

•

QSFP+ to 4 SFP+ (4x10 GbE) direct-attach copper breakout cables, lengths of 1, 3, and 5 m

•

4x10 GbE QSFP+ SR4 compatible with 10GBase-SR SFP+ using 1, 2, 3, 5, 7, 10, 15, and 100 m lengths of fiber cable 

FIGURE 10

QSFP+ to 4 SFP+ (4x10 GbE) breakout cable

The Ruckus ICX 7750 ports available for breakout are shown for each model in 

Table 6

. 

QSFP+ to SFP+ adapter support

The Ruckus ICX 7750 supports a third-party QSFP+ to SFP+ adapter for cost-effective connections between 40 GbE QSFP+ ports and 
10 GbE hardware using standard SFP+ optical cabling rather than breakout cables.

An SFP+ transceiver (SR, LR, or USR) inserted in the QSFP+ to SFP+ adapter behaves as if it is connected to the first of the 4 breakout 
ports on the 40 GbE QSFP+ interface with no other ports available in the breakout. The 4x10 GbE breakout mode must be configured on 
the QSFP+ interface.

10G-SFPP-TX-A transceiver support

The 10G-SFPP-TX-A transceiver consumes significantly more power than typical 10G transceivers. This section provides guidelines for 
deploying the 10G-SFPP-TX-A transceiver within the power capabilities of the supported ICX 7750-48F switch.

If the guidelines in this section are not followed, there is a risk of system instability and/or reboot.

Follow the guidelines provided in 

Table 7

 to avoid a power violation.

For each 10G-SFPP-TX-A installed, another SFP+ slot MUST be left empty.

TABLE 6

Ruckus ICX 7750 40 GbE breakout ports

Model

Front panel Slot 1 ports

Front panel Slot 2 ports

Rear module Slot 3 ports

ICX 7750-26Q

1/1/5 through 1/1/16

1/2/1 through 1/2/6

1/3/1 through 1/3/6

ICX 7750-48F

N/A

1/2/1 through 1/2/6

1/3/1 through 1/3/6

ICX 7750-48C

N/A

1/2/1 through 1/2/6

1/3/1 through 1/3/6

Summary of Contents for Ruckus ICX 7750




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands