CommScope Ruckus ICX 7750 Hardware Installation Manual Download Page 57

Page: 57 / 91

Ruckus ICX 7750 Switch Hardware Installation Guide

Part Number: 53-1003900-10

Ruckus ICX 7750 Operation

LED patterns

FIGURE 41

Ruckus ICX 7750 rear-panel LEDs

LED patterns

The following tables describe the Ruckus ICX 7750 LED patterns.

Management port 10/100 Mbps link/activity
LEDs

UP port (left) and DN port (right) link status LEDs

Management port 1000 Mbps link/activity LEDs

Lower slot 40 GbE mode link/activity LED or 10
GbE mode lane 1 link/activity LEDs

Upper slot 40 GbE mode link/activity LED or
10 GbE mode lane 1 link/activity LEDs

Lower slot 10 GbE mode lanes 2, 3, and 4
link/activity LEDs

Upper slot 10 GbE mode lanes 2, 3, and 4
link/activity LEDs

Expansion module power LED

TABLE 10

PSU1 and PSU2 LEDs

LED state

Status of hardware

Recommended action

Off (no light)

System is off or there is no power.

Verify the system is on and has completed booting.

Steady green

PSU is on and functioning properly.

No action required.

Steady amber

PSU is missing power or in a faulty state.

Verify that the PSU power cord is connected to a
functioning power source.

Replace power supply.

TABLE 11

DIAG LED

LED state

Status of hardware

Recommended action

Off (no light)

Diagnostic is off.

No action required.

Blinking green

System self-diagnostic test is in progress.

No action required.

Steady green

System self-diagnostic test is successfully completed.

No action required.

Steady amber

System self-diagnostic test has detected a fault.

Contact support.

Summary of Contents for Ruckus ICX 7750



























































































Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands

CommScope Ruckus ICX 7750, Hardware Installation Manual

Search results

Summary of Contents for Ruckus ICX 7750

Reviews:

Brands by name

Popular brands