background image

Telephone Interface

G8-S0/G3-S0-I

22

1.1/1010

Telephone Interface

Auto Dialler Mode

A call from an Intercom station or an input message is transferred to a pre-defined telephone number.
The call is transferred to another telephone number after a configurable time if the call is not answered
(i.e. taken over with a password) by this telephone, or immediately if the telephone is busy. 
The order, in which the telephone numbers shall be dialled, is defined in “Dialling sequences“.

Telephone numbers, Dialling sequences

Up to 

8 telephone numbers

 can be defined, which will be dialled in case of an outgoing call.

For each telephone number 

up to 24 digits

 are possible.

These telephone numbers can be arranged in up to 

8 different dialling sequences

The dialling sequences set the order, in which the telephone numbers will be dialled. 

The dialling sequences are selected with 

inputs

, to which e.g. a time switch is connected.

Each dialling sequence can contain up to 

15 telephone numbers

; each number can be dialled se-

veral times (i.e. for a number it is possible to appear in one dialling sequence several times).  

Example

Telephone numbers:

1. 123456 (“Guard 1“)
2. 456789 (“Guard 2“)
3. 0663/0815 (“Mobile Phone 1“)
4. 0663/4711 (“Mobile Phone 2“)

In the daytime, dialling sequence 1 is selected by a time switch.

When a call is initiated, the 1st telephone number of dialling sequence 1 is dialled (“Guard 1“). If the
call is not answered within a configurable time or if the number is busy, the next telephone number
of dialling sequence 1 is dialled, and so forth until the end of the dialling sequence (“Guard 2“–
“Guard 1“ – “Guard 2“...).

At a certain point of time (nighttime), dialling sequence 2 is selected by the time switch. The order
of the calls now is: 3 x “Mobile Phone 1“, then 3 x “Mobile Phone 2“. 

Note:

In case, the call is not taken over by the last telephone number, it is possible to restart the dialling se-
quence 

see page 22

.

Dialling  sequence  1:

1

2

1

2

1

2

1

Dialling  sequence  2:

3

3

3

4

4

4

Activation via inputs

Dialling Sequence 1:

1st no.

0663/...1

2nd no.

0663/...2

3rd no.

0663/...3

4th no.

0663/...1

...........

15th no.

0663/...15

Dialling Sequence 2:

1st no.

0663/...3

2nd no.

0663/...4

3rd no.

0663/...3

4th no.

0663/...5

...........

15th no.

0663/...11

:

:

:

:

:

:

Dialling Sequence 8:

1st no.

0663/...7

2nd no.

0663/...7

3rd no.

0663/...8

4th no.

0663/...8

...........

15th no.

0663/...20

Summary of Contents for C-G3-S0-I



































Reviews: