background image

G8-S0/G3-S0-I

Telephone Interface

1.1/1010

29

Example:       

Call from telephone to Intercom Server

same as in auto dialler mode 

see page 23

Cancel Conversation

At the Intercom station the conversation is cancelled with 

X

.

At the telephone the conversation is cancelled with # or by hanging up.

Speech Control

same as in auto dialler mode 

see page 24

Indication of Telephone Number in Display

The telephone number dialled is shown in the display. 
A cursor indicates if dialling has been completed.

EE811                                                    EE411

As soon as the conversation is established the cursor disappears and after dialling in the Intercom
Server is possible (e.g. conference). 

77

 switches back to telephone dialling for 8 seconds.

Call Request in PABX Mode

It is possible to combine Auto Dialler Mode for Call Requests with the PABX Mode. So the Intercom
stations can dial to any desired telephone number, in case of a call request or input message Auto
Dialler mode is activated automatically.

PA-Code in CCT 800

Dialable Telephone Numbers

4***

4000 – 4999

63**

6300 – 6399

345*

3450 – 3459

5*

50 – 59

Attention:

 

Observe collisions with Intercom call numbers and function codes (i.e. in case of a defined range of 
“2***”, e.g. the Intercom call number “210” can not be dialled)!

X-Cancel

œ

  Volume

Telephone 145

6642324252627_

0043

Summary of Contents for C-G3-S0-I



































Reviews: