ComAp IG-NT Installation Manual Download

Page: 104 / 149

IGS-NT Installation Guide

104

12.2.

Possible Connections per Port

Port Type On

Hardware

Number of
Connections

Available Connections

RS232(1)

Any

InteliVision 8
PC
Modbus terminal
Modem

RS485(1)

IG-NT-BB
IG-NTC-BB
IM-NT-BB
IM-NTC-BB

InteliVision 8
InteliVision 5
IG-Display

RS485(1)

IS-NT-BB
IS-NTC-BB

InteliVision 8
InteliVision 5
IS-Display

RS485(1)

IG-NT
IG-NTC
IM-NT

InteliVision 8
PC
Modbus terminal
Modem

RS232(2)

Where
available

InteliVision 8
PC
Modbus terminal
Modem

RS485(2)

Where
available

InteliVision 8
PC
Modbus terminal
Modem

CAN1

Any

AIN (10x)
BIN (12x)
AOUT (4x)
BOUT (12x)
DENOX20 (1x)
ECON3 (1x)
ECON4 (1x)
Other specialized HW

CAN2

Any

Controllers
InteliVision 8
IG-IB
I-LB+
InternetBridge-NT

USB

Where
available

Ethernet

Where
available

Standard Ethernet Connection

OTE

RS232(1)

– RS485(1) and RS232(2) – RS485(2) can be switched and only one port at a time

is available for communication.

Summary of Contents for IG-NT






















































































































































Search results

Summary of Contents for IG-NT

Reviews:

Related manuals for IG-NT

Brands by name

Popular brands

ComAp IG-NT, Installation Manual

Search results

Summary of Contents for IG-NT

Reviews:

Related manuals for IG-NT

Brands by name

Popular brands