8
ColourCyc 250 LX
may operate in one of 3 modes:
8.1 Automated operation “solo”
8.2 Operation via DMX 512
8.3 Synchronising multiple ColourCyc 250 LXs in the absence of DMX 512 signal.
Depending upon which mode you wish to operate in, you should consult the appropriate instructions below:
8.1 Automated operation “solo”
ColourCyc 250 LX
may operate independently, executing pre-recorded programs which cause it to change colours depending
upon the settings imposed by the dip switches located on the rear panel
In this mode of operation, there is no connection to the unit via the XLR 3 sockets labeled DMX 512 in and out.
8.2 Operation via DMX 512 signal.
Control signal is digital, and is transmitted via two pair screened ø0.5mm cable.
Connection is serial, utilising the XLR 3 male and female sockets located on the base of the
ColourCyc 250 LX
.
Signal connection
Pin connections conform to the international standards:
pin 1= gnd
pin 2= data –
pin 3= data +
Ensure that all data conductors are isolated
from one another and the metal housing of
the connector.
Note:
the housing of the cannon XLR
must not be connected under any cir-
cumstances.
Pin number 1 must be disconnected
from the electrical connection of the
unit.
If your controller utilises an XLR 5 socket, you should respect the polarity of pins 1, 2 and 3 and not connect pins 4 and 5.
3 pin XLR 3/M
3 pin XLR 3/F
made in italy by
coemar
spa
Castel Goffredo (mn)
factor
y set main at:
100V
115V
208V
230V
240V
50Hz
60Hz
DMX OUT
DMX IN
5AT @230V
8AT @115V
POWER
fan
alert
lamp
status
DMX
test fan ON
lamp ON
DR1 remote
motor
calibration
shutter/strobe
inhibit
OFF - DMX addressing, ID personality
ON - built in program control
ON
ON
reset
1
2
4
8
16
32
64
128
256
PR 1
PR 2
PR 3
PR 4
SP 1
SP 2
SP 3
SP4
all PR
DMX addresses, ID personality or built in program and speed
all OFF for slave
serial number
230v
ie max: 2A
ie: 1,6A
115v
ie max: 4,2A
ie: 3,2A
max temp
ext:
150
°
C
ta max:
40
°
C
cos
ϕ
:
0,9
IP 20
weight:
18,4 kg
alto/top
2 m
2 m
dip-switches
Warning!
High voltage inside. Caution: hot lamp. Disconnect from power supply before
opening. A good ground connection is essential. Case is very hot. Do not install on
flammable surfaces. Min. Distance from flammable materials to all exterior surfaces:
0,5m. Important safety information, see instruction manual before use.
made in italy by
coemar
spa
Castel Goffredo (mn)
factor
y
set main at:
100V
115V
208V
230V
240V
50Hz
60Hz
DMX OUT
DMX IN
5AT @230V
8AT @115V
POWER
fan
alert
lamp
status
DMX
test fan ON
lamp ON
DR1 remote
motor
calibration
shutter/strobe
inhibit
OFF - DMX addressing, ID personality
ON - built in program control
ON
ON
reset
1
2
4
8
16
32
64
128
256
PR 1
PR 2
PR 3
PR 4
SP 1
SP 2
SP 3
SP4
all PR
DMX addresses, ID personality or built in program and speed
all OFF for slave
serial number
230v
ie max: 2A
ie: 1,6A
115v
ie max: 4,2A
ie: 3,2A
max temp
ext:
150
°
C
ta max:
40
°
C
cos
ϕ
:
0,9
IP 20
weight:
18,4 kg
alto/top
2 m
2 m
dip-switches
Warning!
High voltage inside. Caution: hot lamp. Disconnect from power supply before
opening. A good ground connection is essential. Case is very hot. Do not install on
flammable surfaces. Min. Distance from flammable materials to all exterior surfaces:
0,5m. Important safety information, see instruction manual before use.
in
out
in
out
Controller
DMX 512
OUT
3
2
1
Ad altri
ColourCyc
250 LX
Connect to other
ColourCyc
250 LX
8. Signal connection
English
