background image

ZEFNET-40-PRO

ZEFNET-60-PRO

ZEFNET-80-PRO

PLUG STANDARD

SAE J1772

NUMBER OF PLUGS

2

TOTAL MAX KW RATING

15.4 kW (2 X 7.7kW)

23kW (2 X 11.5kW)

30.8kW (2 X 15.4kW)

CIRCUIT BREAKER RATING 

2 X 40A

2 X 60A

2 X 80A

MAXIMUM CURRENT

2 X 32A

2 X 48A

2 X 64A

SERVICE INPUT

2 X 208V to 240V, 40A/60A/80A, single phase, 2 wire + grounding

CHARGER OUTPUT

2 X 208V to 240V, 32A/48A/64A continuous (power sharing capable)

HARDWARE FEATURES

OVERALL HEIGHT

84.2 inches / 2,138.68 mm

OVERALL DEPTH

8.5 inches / 215.90 mm 

OVERALL WIDTH

19.0 inches / 482.60 mm (Pedestal-only is 10.4 inches / 264.16 mm)

TOTAL WEIGHT

180 lbs / 81.6466 kg

WALL FLUSH CAPABLE

Yes, units can mount flush to wall  

(bottom or side entry for electrical service conduit/conductor)

STATUS LEDS

Over 5 feet of high visibility LED strips on front and

back of the top of machine w/ L & R plug-specific notifications

ANCHOR BOLT PATTERN

Compatible with most current and legacy units

PLUG DURABILITY/SERVICEABILITY

Rubber over-molded, Type 4X watertight and corrosion resistant plugs,  

impact and crush resistant w/5-year warranty and field-replaceable latches

CABLE LENGTH

23 feet per plug

CABLE MANAGEMENT

Integrated into pedestal

INTEGRATED SERVICE  

RATED BREAKER PANEL

Optional (located in base of unit, front access)

SERVICE GROUND MONITOR

Constantly checks for presence of proper safety ground

CIRCUIT RECLOSURE

Automatic circuit reclosure after minor power faults

CHARGE CIRCUIT 

INTERRUPTION DEVICE

Ground fault protection with fully automated self-test, eliminates manual user testing

EASE OF INSTALLATION

Arrives fully assembled, conduit routing via base or side, bolt pattern matches legacy units

EV DRIVER POINT-OF-SALE & ACCESS CONTROL

SMARTPHONE APP

Standard

CREDIT CARD SWIPE + 

RFID + NFC CAPABILITIES 

Optional (this option adds a VFD screen)

CONNECTIVITY

COMMUNICATIONS

4G cellular modem (Wi-Fi option also available) + Bluetooth

COMPATIBILITY

OCPP and OpenADR compliant

SAFETY & OPERATIONAL RATINGS

CERTIFICATIONS

ETL and cETL listed

FCC

Compliant with Part 15 of FCC rules

NEMA RATING

NEMA 4 - Indoor/outdoor rated, fully sealed, waterproof, and corrosion-resistant enclosure.

OPERATING TEMP/HUMIDITY

Non-derated performance across full -30F to +122F (-40C to 50C)  

range with relative humidity of 95%

Technical Specifications

Summary of Contents for ZEF ENERGY ZEFNET-40-PRO





































Reviews: