Climax FF5300, Operating Manual

Page: 57 / 86

P/N 91025, Rev. 4 Page 45
5 MAINTENANCE
IN THIS CHAPTER:
5.1 M
AINTENANCE CHECKLIST
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -45
5.2 L
UBRICATING THE MACHINE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -46
5.3 A
PPROVED LUBRICANTS
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -47
5.4 M
AINTENANCE TASKS
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -49
5.4.1 C
HECK THE
PCU
OIL RESERVOIR LEVELS
- - - - - - - - - - - - - - - - - - - - - - - - - - - -49
5.4.2 E
MPTY THE AIR FILTER WATER TRAP
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -49
5.4.3 PCU
EMERGENCY STOP CHECK
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -49
5.4.4 PCU
DROP
-
OUT CIRCUIT CHECK
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -49
5.4.5 D
OVETAIL WAYS MAINTENANCE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -50
5.4.6 L
EADSCREW MAINTENANCE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -50
5.4.7 A
DJUST THE DOVETAIL WAYS GIB SCREWS
- - - - - - - - - - - - - - - - - - - - - - - - - - - -50
5.5 T
ROUBLESHOOTING
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -51
5.5.1 T
HE MACHINE ISN
’
T TURNING
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -51
5.5.2 T
HE MACHINE ISN
’
T FEEDING
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -51
5.5.3 T
HE MACHINE IS PERFORMING POORLY
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -51
5.5.4 T
HE MACHINE IS NOT CUTTING FLAT
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -52
5.6 D
ECOMMISSIONING
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -52
5.1 M
AINTENANCE CHECKLIST
This chapter explains periodic maintenance intervals and tasks and provides trou-
bleshooting guidance.
CAUTION
Failure to properly clean and maintain the machine can result in
machine damage and void the warranty.
Always keep moving machine parts clear of metal chips.
Following the required maintenance schedule is critical to obtaining normal
machine life.
Keep all machine components in clean, working condition.
Check that parts such as the mounting surfaces, hydraulic fittings, and the tools
themselves are free of metal chips, nicks, and burrs.
To prevent corrosion, thoroughly rinse with fresh, clear water any machine parts
that are exposed to salt water.