6
TM12-1109 | 2019-02
Apex Tool Group
1
EN
2.2 Operator Training
The tightening system may only be put into operation,
adjusted and tested by personnel that have been trained
and qualified by employees of Apex Tool Group.
The tool has been preset by Cleco Production Tools.
Changes to the default settings can only be made by a
qualified employee
1)
.
Additional information can be found in the Programming
Manual.
2.3 Intended Use
This product is part of the Cleco Production Tools' tighten-
ing system. It is intended for use in industrial fastening pro-
cesses. Only use the tool under the following conditions:
•
In conjunction with the components listed in the EC
Declaration of Conformity.
•
Under the prescribed environmental conditions.
•
With the recommended supply voltage.
•
Within the power range, which is specified in the techni-
cal data.
•
In EMC Limit Class A (electromagnetic immunity for
industrial areas). For the currently observed EMC stan-
dards, see the EC Declaration of Conformity.
DO NOT use the tool as a hammer.
DO NOT use a controller other than the one listed in
the EC Declaration of Conformity.
DO NOT use the tool in potentially explosive areas.
DO NOT use the tool in damp spaces or outdoors.
DO NOT disassemble or modify the tool.
2.4 General Power Tool Safety
Warnings
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injuries.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to mains-oper-
ated (corded) power tool or battery-operated (cordless)
power tool.
1 Work Area Safety
a)
Keep your work area clean and well lit.
Cluttered or
dark areas invite accidents
.
b)
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liq-
uids, gases or dust.
Power tools create sparks which
may ignite the dust or fumes.
c)
Keep children and bystanders away while operat-
ing a power tool.
Distractions can cause you to lose
control.
2 Electrical Safety
a)
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b)
Avoid body contact with earthed or grounded sur-
faces, such as pipes, radiators, ranges and refrig-
erators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c)
Do not expose power tools to rain or wet condi-
tions.
Water entering a power tool will increase the
risk of electric shock.
d)
Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts.
Damaged or entangled cords increase the risk
of electric shock.
3
Personal Safety
a)
Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication.
A
moment of inattention while operating power tools may
result in serious personal injury.
b)
Use personal protective equipment. Always wear
eye protection.
Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing pro-
tection used for appropriate conditions will reduce per-
sonal injuries.
c)
Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d)
Remove any adjusting key or wrench before turn-
ing the power tool on.
A wrench or a key left attached
to a rotating part of the power tool may result in per-
sonal injury.
e)
Do not overreach. Keep proper footing and bal-
ance at all times.
This enables better control of the
power tool in unexpected situations.
f)
Dress properly. Do not wear loose clothing or jew-
ellery. Keep your hair and clothing away from mov-
ing parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g)
Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles.
A careless action can cause
severe injury within a fraction of a second.
CE compliant
The product corresponds to the prescribed
technical requirements in Europe.
Observe and comply with all local disposal
guidelines for all components of this equip-
ment and it’s packaging.
1.Qualified employees have the training and experi-
ence to identify potentially hazardous situations.
They can initiate appropriate safety measures and
are obliged to comply with regulations.
Summary of Contents for NeoTek 30 Series
