Cisco WRT350N Quick Installation Manual Download

Page: 13 / 204

Tilslut den ene ende af et

Ethernet-kabel til en af de

nummererede porte bag på

routeren. Tilslut den anden ende

til en Ethernet-port på en

netværksenhed, f.eks. en pc,

printerserver eller switch.

Gentag dette trin for at tilslutte

flere pc'er eller andre

netværksenheder til routeren.

Tænd bredbåndsmodemmet.

Tilslut den medfølgende

strømforsyning til routerens

strømstik, og tilslut derefter

strømforsyningen til en

stikkontakt. Lysdioden Power på

frontpanelet lyser, når

strømforsyningen er tilsluttet

korrekt.

Tænd pc'en/pc'erne.

Find en velegnet placering til

routeren. Den bedste placering

er normalt midt i det trådløse

netværk med fri sigtelinje til alle

dine trådløse enheder.

Fortsæt til trin 2.

VIGTIGT:

Brug den

strømforsyning, der følger med
routeren. Brug af en anden
strømforsyning kan beskadige
routeren.

Summary of Contents for WRT350N













































































































































































































Search results

Summary of Contents for WRT350N

Reviews:

Related manuals for WRT350N

Brands by name

Popular brands

Cisco WRT350N, Quick Installation Manual

Search results

Summary of Contents for WRT350N

Reviews:

Related manuals for WRT350N

Brands by name

Popular brands