Cisco WRT350N Quick Installation Manual Download

Page: 177 / 204

Appendix C: Upgrading Firmware

Wireless-N Gigabit Router with Storage Link

Appendix C: Upgrading Firmware

The Router's firmware is upgraded through the Web-based Utility's Administration tab. Follow these instructions:

1. Download the firmware from Linksys's website at

www.linksys.com/international

2. Extract the firmware file on your computer.

3. Open the Router’s Web-based Utility, and click the

Administration

tab.

4. Click the

Firmware Upgrade

tab, and the

Firmware Upgrade

screen will appear.

5. Enter the location of the firmware's file, or click the

Browse

button to find the file.

6. Click the

Start to Upgrade

button, and follow the on-screen instructions.

Figure C-1: Firmware Upgrade

Summary of Contents for WRT350N













































































































































































































Search results

Summary of Contents for WRT350N

Reviews:

Related manuals for WRT350N

Brands by name

Popular brands

Cisco WRT350N, Quick Installation Manual

Search results

Summary of Contents for WRT350N

Reviews:

Related manuals for WRT350N

Brands by name

Popular brands