Cisco UC520-24U-8FXO-K9 Overview Download Page 6

Page: 6 / 52

* Only one optional VIC can be factory-installed in a UC 520.

Table 2

UC 520 Interfaces

Description

Label

Value in Software
Configuration

Console/Aux port

CONSOLE

—

Fast Ethernet 10/100 expansion port

EXPANSION

FastEthernet0/1/8

Fast Ethernet 10/100 WAN port

WAN

FastEthernet0/0

Fast Ethernet 10/100 Power over Ethernet
(PoE) ports

Power Over Ethernet, and
PWR 0 LNK to PWR 7
LNK

FastEthernet0/1/0 to 0/1/7

FXS (Foreign Exchange Station) ports

FXS, and

0–3

port 0/0/0 to 0/0/3

FXO (Foreign Exchange Office) ports

FXO, and

0–3

port 0/1/0 to 0/1/3

ISDN BRI ports

B0 - B1

Numbered top to bottom,
port 0/1/0 to 0/1/1

VLAN number for data network

—

Vlan1

VLAN number for voice network

—

Vlan100

Music-on-Hold (MoH) port

voice-port 0/4/0

Compact Flash slot

COMPACT FLASH

flash

(Factory Option) VIC:BRI*

VIC2-2BRI-NT/TE

and 0 -1

port 0/2/0 to 0/2/1

(Factory Option) VIC: FXO*

VIC2-2FXO and 0-1

VIC2-4FXO and 0-3

port 0/2/0 to 0/2/1

port 0/2/0 to 0/2/3

(Factory Option) VIC: FXS*

VIC3-2FXS/DID and 0-1

VIC-4FXS/DID and 0-3

VIC3-4FXS/DID and 0-3

port 0/2/0 to 0/2/1

port 0/2/0 to 0/2/3

T1/E1

VWIC2-1MFT-T1/E1

port 0/3

Summary of Contents for UC520-24U-8FXO-K9





















































Search results

Summary of Contents for UC520-24U-8FXO-K9

Reviews:

Related manuals for UC520-24U-8FXO-K9

Brands by name

Popular brands

Cisco UC520-24U-8FXO-K9, Overview

Search results

Summary of Contents for UC520-24U-8FXO-K9

Reviews:

Related manuals for UC520-24U-8FXO-K9

Brands by name

Popular brands