Cisco UC520-24U-8FXO-K9 Overview Download Page 32 | Manualshive

Page: 32 / 52

background image

32

9

Installing a Cisco Catalyst Express 520 for a UC 520

Before you install the switch, review the information in the Release Notes for the Catalyst Express 520
Switches on Cisco.com.

Before you power on or install the switch, review the safety information in the

“Warning Definitions”

section on page 32

and the

“Installation Guidelines” section on page 36

.

The warnings in this chapter are translated into different languages in the Regulatory Compliance and
Safety Information for the Catalyst Express 520 Switches document on Cisco.com.

This section contains basic installation information including the following:

•

Warning Definitions

•

Installation Guidelines

•

Desktop Installation

•

Connecting the Switch to the UC 520

•

Adding a Switch to a Community

Warning Definitions

These warnings are translated into different languages in the Regulatory Compliance and Safety
Information for the Catalyst Express 520 Switches document that ships with the switch. Review these
warnings before you power on or install the switch.

«
...
30
31
32
33
34
...
»

Summary of Contents for UC520-24U-8FXO-K9





















































Reviews:

No comments

Related manuals for UC520-24U-8FXO-K9

DocuPrint N4025

Brand: Xerox Pages: 129

Brand: Yamaha Pages: 37

Brand: Nero Pages: 76

IFOLDER 3 - ADMINISTRATION

Brand: Novell Pages: 148

Brand: Davis Instruments Pages: 108

Discover ActiveX

Brand: Teklynx Pages: 165

Lancast Media Converter 7000

Brand: Cabletron Systems Pages: 108

Brand: Paradyne Pages: 24

Brand: Avaya Pages: 48

drivers for video card

Brand: EVGA Pages: 23

Brand: Measurement Computing Pages: 109

ANTI-VIRUS 2011 - REV 2011.07

Brand: AVG Pages: 210

ANTI-VIRUS 2011 - REV 2011.06

Brand: AVG Pages: 210

Brand: ION Pages: 12

Brand: Intel Pages: 30

Aurora Edit Security

Brand: GRASS VALLEY Pages: 5

15606-011408-9320 - MAP R6.3 CPU MODEL-UPG 4/5 MIN 2 CPUS INITL

Brand: Autodesk Pages: 190

Brand: Focusrite Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands